base-boards

Operation requires both a base board and a core module.

RAK5005-O

:::caution The RAK5005-O is no longer in production. It is recommended to use the RAK19007 instead. :::

• RAK5005-O - The original WisBlock Base Board.
• Slots
• (x1) Core Module slot
• (x1) WisBlock IO Module slot
• (x4) WisBlock Sensor Module slots
• Buttons
• (x1) Reset Button
• It may be possible to add a user button using the 13002 IO module.
• Connectors
• JST PHR-2 connector for 3.7v LiPo battery (with charge controller)
• JST-ZHR-2 connector for 5v solar panel (max 5.5v)
• I²C, UART, GPIOs and analog input accessible with solder contacts
• Micro USB port for debugging and power
• Screen Support
• OLED screen support (OLED screen sold separately)

:::note The RAK5005 (without the -O) is not compatible. :::

Connectors Diagram

Voltages

• JST PHR-2 connector for 3.7v LiPo battery.
• Charge controller max charge rate is 500mAh.
• Minimum input voltage for charging is 3.3v, maximum 4.3v.
• JST ZHR-2 connector for 5v solar panel.
• Minimum input voltage to charge is 4.4v, maximum 5.5v.

Further information on the RAK5005-O can be found on the RAK Documentation Center.

RAK19007

• RAK19007 - WisBlock Base Board (2nd Generation, an upgrade to the RAK5005-O)
• Slots
• (x1) Core Module slot
• (x1) WisBlock IO Module slot
• (x4) WisBlock Sensor Module slots
• Buttons
• (x1) Reset Button
• To add a user button, you can utilize the AIN1 pin, which is exposed as pin 31 in the firmware.
• Connectors
• JST PHR-2 connector for 3.7v LiPo battery.
• JST ZHR-2 connector for 5v solar panel.
• I²C, UART, BOOT and GPIOs accessible with solder contacts
• USB-C port for debugging and power
• Screen Support
• OLED screen support (OLED screen sold separately)

Further information on the RAK19007 can be found on the RAK Documentation Center.

Connectors Diagram

Voltages

• JST PHR-2 connector for 3.7v LiPo battery.
• Charge controller max charge rate is 350mAh.
• Minimum input voltage for charging is 3.3v, maximum 4.3v.
• JST ZHR-2 connector for 5v solar panel.
• Minimum input voltage to charge is 4.4v, maximum 5.5v.

Resources

• Purchase Links:
• US
  • Rokland
  • muzi ᴡᴏʀᴋꜱ Starter Kit
• International
  • RAKwireless
  • RAKwireless Starter Kit
  • RAKwireless AliExpress
  • RAKwireless AliExpress Starter Kit

RAK19003

• RAK19003 - WisBlock's Mini Base Board.
• Slots
• (x1) Core Module slot
• (x2) WisBlock Sensor Module slots
• Buttons
• (x1) Reset Button
• Connectors
• JST PHR-2 connector for 3.7v LiPo battery.
• JST ZHR-2 connector for 5v solar panel.
• I²C, UART and BOOT headers accessible with solder contacts
• USB-C port for debugging and power
• Screen Support
• OLED screen support (OLED screen sold separately)

Further information on the RAK19003 can be found on the RAK Documentation Center

Connectors Diagram

Voltages

• JST PHR-2 connector for 3.7v LiPo battery.
• Charge controller max charge rate is 350mAh.
• Minimum input voltage for charging is 3.3v, maximum 4.3v.
• JST ZHR-2 connector for 5v solar panel.
• Minimum input voltage to charge is 4.4v, maximum 5.5v.

Resources

• Purchase Links:
• US
  • Rokland
• International
  • RAKwireless
  • RAKwireless AliExpress

RAK19001

• RAK19001 - WisBlock's Dual IO Base Board.
• Slots
• (x1) Core Module slot
• (x2) WisBlock IO Module slot
• (x6) WisBlock Sensor Module slots
• Buttons
• (x1) Reset Button
• (x1) User-defined push button switch
• (x1) Battery selector switch
• On this board the PIN for user button (IO5) is available as a solder contact on the upper header row.
• Connectors
• JST PHR-2 connector for 3.7v LiPo battery (with charge controller)
• JST ZHR-2 connector for 5v solar panel (max 5.5v)
• Separate FGH20005-S02M2W1B connector for non-rechargeable batteries
• I²C, SPI, UART, BOOT and GPIOs accessible with solder contacts
• USB-C port for debugging and power
• Screen Support
• OLED screen support (OLED screen sold separately)

Further information on the RAK19001 can be found on the RAK Documentation Center.

Connectors Diagram

Voltages

• JST PHR-2 connector for 3.7v LiPo battery.
• Charge controller max charge rate is 500mAh.
• Minimum input voltage for charging is 3.3v, maximum 4.3v.
• JST ZHR-2 connector for 5v solar panel.
• Minimum input voltage to charge is 4.4v, maximum 5.5v.
• FGH20005-S02M2W1B connector for non-rechargeable battery.
• Minimum required is 3.3v, typical 3.7v, maximum 5.5v.
• Active battery is selected with the battery selector switch.

Resources

• Purchase Links:
• US
  • Rokland
• International
  • RAKwireless
  • RAKwireless AliExpress